Leaks around the chimney fixed properly, not caulked over

Chimney Flashing Repair in the Bay Area

The joint where a chimney passes through the roof is one of the most common places for a roof to leak. The fix is almost never more caulk. We rebuild the flashing the way it is meant to work, with metal layered so water is carried around the chimney and off the roof.

Get a Free Chimney Flashing Estimate

No obligation · Response within 30 minutes

Chimney Flashing

How Chimney Flashing Keeps Water Out

A chimney and a roof move independently. The house settles, the wood expands and shrinks with the seasons, and the masonry does not move with it. That is why a chimney cannot simply be sealed to the roof. It needs a system of overlapping metal pieces that shed water while letting the two surfaces move.

 

Step flashing runs up each side of the chimney in short L-shaped pieces, each one woven in with a course of shingles. Counter flashing, sometimes called cap flashing, is set into the mortar joints of the chimney and folds down over the step flashing, so water running down the brick lands on the outside of it. An apron covers the downhill face. On the uphill side, a wide chimney gets a cricket, a small peaked structure that splits the water and debris around the chimney instead of letting it dam up behind it.

 

When any of those pieces are missing, loose or replaced with a bead of roofing cement, water finds its way in. Chimney leaks are one of the most common causes we find on roof leak repair calls.

Chimney Flashing Services

What We Do Around Chimneys

Every part of the chimney-to-roof joint, rebuilt to work together.

Step Flashing

Side flashing replaced and woven in with the roofing.

Counter Flashing

Cap flashing cut into the mortar joints and sealed.

Chimney Crickets

Crickets framed and flashed behind wide chimneys.

Apron Flashing

The downhill face of the chimney flashed and lapped correctly.

Leak Tracing

Water tested to confirm whether the leak is the flashing or the masonry.

Flashing With a New Roof

Chimney flashing replaced, never reused, during a re-roof.

Framed Chimney Chases

Flashing for framed chimneys and chases on newer or rebuilt homes.

Tile and Metal Roofs

Chimney flashing detailed for tile and metal roofing.

Common Problems

Why Chimney Flashing Fails

Caulk and roofing cement instead of flashing

The most common problem we find is not worn flashing but missing flashing, with a thick smear of roofing cement or caulk doing the job instead. It may hold for a season or two, but it dries, cracks and pulls away as the roof and chimney move. Adding more sealant on top only buys a little time.

Counter flashing pulled out of the mortar

Counter flashing is held in a groove cut into the mortar. When the mortar weathers or the flashing was only surface-mounted with sealant, it loosens and water runs behind it and straight down the step flashing into the roof.

Rusted or damaged metal

Older galvanized flashing rusts through, especially at the bends. Flashing can also be bent or lifted by wind, falling branches or someone walking on the roof during chimney or satellite work.

No cricket

A wide chimney without a cricket acts like a dam. Water and leaves pile up behind it, and that standing water eventually works its way under the roofing. Building codes generally require a cricket once a chimney reaches a certain width, but many older roofs were built without one.

When the leak is not the flashing

Not every chimney leak is a flashing problem. Water can also get in through a cracked chimney crown, a missing chimney cap or porous, cracked brick and mortar. We water test to find out which it is. Masonry repair is a different trade, and if that is the source we will tell you rather than replace flashing that is not the problem.

Chimneys after earthquakes

Many older Bay Area chimneys have been damaged, braced or rebuilt after earthquakes, and some have been replaced with framed chases covered in siding. Each type needs its own flashing details, and a chimney that has shifted often needs its flashing redone even if the roof around it is fine.

How It Works

How a Chimney Flashing Repair Works

1

Call Us

Call or send the form and tell us where you are seeing water or stains.

2

Schedule

We inspect the chimney, flashing and attic, and water test if needed to confirm the source.

3

We Work

Old flashing and sealant removed, new step, counter and apron flashing installed, cricket if needed.

4

Follow-Up

We check the finished work together and water test again to confirm the leak is stopped.

Signs of Trouble

Signs Your Chimney Flashing Is Leaking

Chimney flashing leaks usually show up inside first: a water stain on the ceiling or wall beside the chimney, peeling paint or damp drywall near the fireplace, or dark, wet wood around the chimney in the attic. From outside, look for flashing that is lifted, rusted or missing, gaps between the metal and the brick, or heavy patches of black roofing cement where flashing should be.

 

Replacing the roof is the best time to replace chimney flashing, and it should never be reused on a new roof. For prices, see chimney flashing repair cost. If you are planning a roof replacement, it is included. If water is already coming in, call (707) 470-7181 or see emergency roof repair.

Common Questions

Chimney Flashing Questions

How do I know if my chimney flashing is leaking?

Water stains or damp drywall on the ceiling or wall next to the chimney are the most common sign. In the attic, look for wet or darkened wood around the chimney. Outside, lifted, rusted or missing flashing, or heavy patches of roofing cement, point to a problem.

Can chimney flashing be repaired, or does it need replacing?

A small section that has lifted can sometimes be refastened and resealed. When the flashing is rusted, missing or was never installed correctly, replacing it is the fix that lasts.

Is sealing the flashing with caulk enough?

Only as a short-term patch. Caulk and roofing cement dry out and crack as the chimney and roof move. Properly layered step and counter flashing sheds water without relying on sealant.

What is a chimney cricket?

A small peaked structure built on the uphill side of a wide chimney. It splits water and debris around the chimney so they do not pool behind it. Codes generally require one once a chimney reaches a certain width.

Should chimney flashing be replaced with a new roof?

Yes. Old flashing should not be reused on a new roof. New step, counter and apron flashing is installed as part of the replacement so the new roof does not leak at its most common weak point.

Service Area

Chimney Flashing Repair Across the Bay Area

We repair chimney flashing from our base in Suisun City across Solano County, Napa County, Contra Costa County, Alameda County and the rest of the Bay Area.